|
Home
Products
Programmers
PRESTO
FORTE
Logic analyzers
SIGMA2
OMEGA
USB products
UCAB232
UCAB232i
Other products
Museum
Electronic Design
Sales & Prices
Support
About us
Contact
|
|
Comparison of SIGMA2 and OMEGA
|
Parameter
|
SIGMA2
|
OMEGA
|
Standard mode
(with advanced trigger logic)
|
16 inputs / 50 MSPS
|
16 inputs / 200 MSPS
|
Accelerated mode
(with simple triggering)
|
◊ 8 inputs / 100 MSPS
◊ 4 inputs / 200 MSPS
|
8 inputs / 400 MSPS
|
|
PC interface
|
USB 2.0 Full Speed (12 Mbps)
powered from USB, no external supply required
|
USB 2.0 High Speed (480 Mbps)
powered from USB, no external supply required
|
Sample memory size
Maximal test length - each successive sample differs (data cannot be compressed).
|
14.7 million
|
29.8 million
|
Typical number of samples
Tested with I2C, SPI or UART serial protocols.
|
2 millions input signal changes
|
20 to 30 millions input signal changes
|
Max. test length /
max. test time
Test length / time with no signal changes on the inputs.
|
128 G / 45 min.
|
862 G / 77 min.
|
|
Worst condition test length
|
0.29 s
|
0.15 s
|
|
Maximum compressed data flow
|
915 Mbps
|
3.6 Gbps
|
|
Synchronization
|
N/A
|
◊ 2 analyzers (up to 32 inputs): ±5 ns
◊ 3 analyzers (up to 48 inputs): ±10 ns
◊ more: possible but without timing specification
|
|
On the market
|
Since 2011
(SIGMA since 2007)
|
Since 2012
|
Price
(end user, for 1 unit, w/o VAT)
|
EUR 198.-
|
EUR 298.-
|
Technical details
|
Parameter
|
SIGMA2
|
OMEGA
|
|
Number of inputs
|
16
|
|
Input logic level
|
TTL
|
|
Input buffers
|
74LVC245, TSSOP
|
|
ESD protection
|
27 Ohm serial input resistor + built-in CMOS ESD protection
|
Trigger conditions
in standard mode
|
Advanced, 3 masks
Resolution: 1 sample (20 ns)
|
Advanced, 3 masks
Resolution: 2 samples (10 ns)
|
|
FPGA
|
Xilinx Spartan-3
|
Xilinx Spartan-3A
|
|
Memory
|
SDRAM, 256 Mbit, 16-bit bus, ~66 MHz
|
SDRAM, 512 Mbit, 32-bit bus, ~133 MHz
|
|
Compression method
|
RLE
|
RLE + Huffman coding
|
|
Maximum RLE run count
|
64 K
|
32 K
|
|
External Trigger-In
|
LVTTL (max. 3.3 V)
|
|
External Trigger-Out
|
LVCMOS (3.3 V) with 1 kOhm serial resistor
or open collector with pull-up
|
LVCMOS (3.3 V)
|
|
Auxiliary power output
|
On Trigger-In pin, 2.7 to 3.3 V, max. 100 mA
|
|
Target cables
|
CAB20LA (colored wires with individual numbered sockets)
CAB2020 (20-pin header for 16 channels)
CAB2010 (10-pin header for 8 and 4 channels)
|
CAB20LA (colored wires with individual numbered sockets)
CAB2020 (20-pin header for 16 channels)
CAB2010 (10-pin header for 8 channels)
Synchronization cable
|
|
User interface
|
2 LEDs (green/yellow and red/yellow)
GO button (test ➜ trigger ➜ stop)
|
|
Software
|
All-in-one package: Logic analyzer + utilities +USB Driver + documentation
|
|
Protocol analyzers
|
Free: UART, SPI, I2C, 1-Wire, USB Full Speed (12 Mbps)
|
|
|
